TRD2000 Corrolla p/n's

Hey,

I have been looking for a chassis code for these rare models on the DIY toyota website and have no listing for a 2000 cc model apart from the 2c diesel version
do any of you people know where i could find the info so i could take a look at the specs of the engine mounts and driveshafts etc?

my avenue is that a swap can be made easier if i could find a vin number for one of those trd2000 models and could get a hold of the p/n's needed for the mounts and other bits they used

the 2c may use the same mounts as the 3s? am i on the right track ?

any input would be welcome




here is the diesel mount of a 97 corolla

what i dont get is part number 12315a what is that?



and here is the same year corolla with a 4afe

heres a how-to

http://www.ae101ownersclub.com/t585-3s-ge-swap-into-a-corolla

thankyou

I just went out for a look around my mounts and notices they are bit different to the other guys with 4afe or similar engines?

sorry for being overly cautious i just want to have all the correct bits needed to get stuck into the job

please take a look and let me know if im wrong .......... i see that bolt missing ill keep an eye on that















passenger side

sorry about the pics i had to use the wifes big dildo camera - long lens thing

they all look the same / similar to my stock 4efe ones, before i used the rav4 mount for the cambelt side

miib14 wrote:

they all look the same / similar to my stock 4efe ones, before i used the rav4 mount for the cambelt side

ok thanks also regarding the avensis , we a have a van type thing by that name here - is that the one you guys refer to for the trans mount?

regards

timing belt side engine mount use a Rav4 3sge ax10 mount.

gearbox side use a corolla one and redrill to fit S54 box

Front mount use corolla/celica mount

Rear mount use corolla/celica mount

ok so no need for avensis on the gear box side . can elaborate on re drilling ? the mount on the chassis ?
sorry to be a pain just want to get set up for this

miib14 wrote:

timing belt side engine mount use a Rav4 3sge ax10 mount.

gearbox side use a corolla one and redrill to fit S54 box

Front mount use corolla/celica mount

Rear mount use corolla/celica mount

ok so no need for avensis on the gear box side . can elaborate on re drilling ? the mount on the chassis ?
sorry to be a pain just want to get set up for this

fits on the chassis, just redrill the mount to the holes on top of the gearbox

miib14 wrote:

fits on the chassis, just redrill the mount to the holes on top of the gearbox

thankyou again

Re this : ST182 driver side shaft
MK2 Rev2 MR2 Passenger side shaft

Does that include the inner and outers cvs etc ?

I found a shop on eBay that sells them
NEW And wanting to buy

Or do I need to mix and match inner and outers to fit my ae101 hubs? Or will the fit as they are?

Getting excited!!!

ST182 driver side shaft
MK2 Rev2 MR2 Passenger side shaft

Are these based on a rhd car?

So here is the celica one we do not get the st182 in Australia but we get the st184
http://m.ebay.com.au/itm/181258175770?nav=SEARCH&sbk=1

Not sure if I need the left or right

And for the sw20 I can't find anything in the country as yet

Any input always welcome

yes i have a RHD corolla

im not sure if the CV spline will be same on the gearbox side im afraid.
I maybe able to source you a SW20 Driveshaft, but it wont be cheap to ship them to you

That's ok ill need to do it either way I guess


The st184 has exactly the same box s54
So that should be ok

So long side is celica an short side is sw20 right

yes, so if you have a LHD car then

SW20 would be the drivers side (short shaft)
St182 would be the passenger side (long shaft)

Oh I'm rhd in Australia so I will just reverse that

I just have not heard if you buy the complete shaft with cv included or I I need to change the outer part to suit the ae101 hub.

The other guys here did not mention this so it may not need to happen but I feel I should hold out until I know

Thanks for your help much appreciated

mine is a RHD.
the complete shaft will fit into the hub, i know this as i am running this setup

Oh great so at least I can now buy the celica one - the st182/3 is odd as far as I can see there is absolutely no difference to the st184????

Toyota can be weird sometimes

I guess we will need to talk about that me2 shaft in the coming months

I am waiting on a call back from an imported re: a beams engine set

Can't wait to get started!!

if you need any help let me know

Thanks! I predict that I will

Celica long shaft ordered

Now sw20 shaft

And rav 4 mount to aquire

I have come across a 1990 sw20 3sge with 5 speed driveshaft

Is that one ok guys???


Cheers to all